Please keep at least one language enabled. || కనీసం ఒక భాషను ఎంచుకోండి.
Question 1
ప్రశ్న 1
A rotating shaft transmits torque T at a constant angular speed ω. Which relationship correctly gives the transmitted power P?
Explanation:
Mechanical power transmitted by a rotating shaft is the product of torque and angular velocity. Therefore P = Tω when consistent SI units are used. If torque is expressed in N·m and angular velocity in rad/s, power is obtained in watts. When rotational speed is supplied in revolutions per minute, it must first be converted using ω = 2πN/60. Hence Option B is correct.
వివరణ:
Question 2
ప్రశ్న 2
A shaft transmits 30 kW at 300 rpm. What torque is transmitted approximately?
Explanation:
The angular velocity is ω = 2πN/60. For N = 300 rpm, ω = 10π ≈ 31.416 rad/s. The transmitted torque is T = P/ω = 30000/31.416. This gives approximately 954.9 N·m. Therefore Option B is correct.
వివరణ:
Question 3
ప్రశ్న 3
A shaft transmits 75 kW at 250 rpm. What is the transmitted torque approximately?
Explanation:
The rotational speed must first be converted to angular velocity. Thus ω = 2π × 250/60 ≈ 26.180 rad/s. The torque is T = P/ω = 75000/26.180. This gives approximately 2864.8 N·m. Hence Option D is correct.
వివరణ:
Question 4
ప్రశ్న 4
A solid circular shaft is required to transmit 60 kW at 200 rpm. If the allowable torsional shear stress is 60 MPa, what is the minimum theoretical shaft diameter based only on strength?
Explanation:
At 200 rpm, the angular velocity is 2π × 200/60 ≈ 20.944 rad/s. The corresponding torque is 60000/20.944 ≈ 2864.8 N·m, or 2.8648 × 10^6 N·mm. For a solid circular shaft, τmax = 16T/(πd³). Solving for d with τallow = 60 MPa gives d ≈ 62.42 mm. Therefore Option C is correct.
వివరణ:
Question 5
ప్రశ్న 5
A hollow circular shaft has outside diameter 100 mm and inside diameter 60 mm. If its allowable torsional shear stress is 70 MPa and it rotates at 200 rpm, what is the maximum power it can transmit based on torsional strength?
Explanation:
The hollow-shaft polar section modulus is Zp = π(D⁴ - d⁴)/(16D). For D = 100 mm and d = 60 mm, Zp ≈ 170902.6 mm³. The allowable torque is therefore T = τallow Zp ≈ 11.963 kN·m. At 200 rpm, ω = 20.944 rad/s, so P = Tω ≈ 250.6 kW. Hence Option C is correct.
వివరణ:
Question 6
ప్రశ్న 6
A solid circular shaft 60 mm in diameter and 2 m long is limited to an angle of twist of 1°. If G = 80 GPa and the shaft runs at 500 rpm, what maximum power can it transmit based only on the twist limitation?
Explanation:
For a 60 mm solid shaft, J = πd⁴/32. The allowable torque from the stiffness condition is T = θGJ/L, with θ = π/180 rad. This gives T ≈ 0.8883 kN·m. At 500 rpm, the angular velocity is approximately 52.360 rad/s. Therefore P = Tω ≈ 46.51 kW and Option B is correct.
వివరణ:
Question 7
ప్రశ్న 7
A solid circular shaft 2 m long transmits 40 kW at 300 rpm. The allowable shear stress is 50 MPa, the allowable angle of twist is 1.5°, and G = 80 GPa. Ignoring standard-size rounding, which diameter requirement governs?
Explanation:
The torque corresponding to 40 kW at 300 rpm is approximately 1273.2 N·m. Applying τmax = 16T/(πd³) gives a strength-based diameter of approximately 50.62 mm. Applying θ = 32TL/(πGd⁴) with θ = 1.5° gives a stiffness-based diameter of approximately 59.32 mm. A shaft must satisfy both criteria, so the larger diameter governs. Therefore stiffness controls and Option A is correct.
వివరణ:
Question 8
ప్రశ్న 8
For a solid circular shaft of fixed material and length, which scaling relationships are correct when torque T changes?
Explanation:
For strength, τmax = 16T/(πd³), so a fixed allowable stress gives d³ proportional to T. Hence the strength-controlled diameter varies as T^(1/3). For stiffness, θ = 32TL/(πGd⁴), so a fixed twist limit gives d⁴ proportional to T. Thus the stiffness-controlled diameter varies as T^(1/4). Therefore Option B is correct.
వివరణ:
Question 9
ప్రశ్న 9
A hollow shaft has D = 80 mm and d = 60 mm. A solid shaft of the same material and length is chosen to have the same cross-sectional area. If both are limited by the same allowable torsional shear stress, approximately how many times as much torque can the hollow shaft carry as the equal-area solid shaft?
Explanation:
Equal area requires the solid diameter to satisfy ds² = D² - d². Thus ds = √(80² - 60²) ≈ 52.92 mm. Torque capacity at the same allowable shear stress is proportional to polar section modulus Zp. The ratio Zhollow/Zsolid is approximately 2.362. Therefore the hollow shaft can carry about 2.36 times the torque and Option C is correct.
వివరణ:
Question 10
ప్రశ్న 10
For the equal-area shafts in the previous question, D = 80 mm and d = 60 mm for the hollow shaft and ds ≈ 52.92 mm for the solid shaft. If material and length are the same, what is the approximate ratio of hollow-shaft torsional stiffness to solid-shaft torsional stiffness?
Explanation:
For equal material and length, torsional stiffness GJ/L is proportional to the polar second moment J. The hollow-shaft value is J = π(80⁴ - 60⁴)/32. The equal-area solid shaft has diameter approximately 52.92 mm and J = πds⁴/32. Dividing the two values gives a stiffness ratio of approximately 3.571. Hence Option C is correct.
వివరణ:
Question 11
ప్రశ్న 11
Two circular shaft segments are connected in series and transmit the same torque of 1.2 kN·m. Segment 1 is a solid 50 mm diameter shaft 1 m long, and Segment 2 is a hollow shaft with D = 60 mm, d = 40 mm and length 1.5 m. If G = 80 GPa for both, what is the total angle of twist approximately?
Explanation:
For shaft segments in series, the rotations of the individual segments add algebraically. Segment 1 has θ1 = TL1/(GJ1) ≈ 0.02445 rad. Segment 2 has θ2 = TL2/(GJ2) ≈ 0.02204 rad. Their total rotation is therefore approximately 0.04648 rad. This is approximately 2.66°, so Option B is correct.
వివరణ:
Question 12
ప్రశ్న 12
A shaft is fixed at A and has two applied torques to its right: 2.0 kN·m clockwise at B and 0.8 kN·m counterclockwise at the free end C. There are no other torques. What are the magnitudes of the internal torques in segments AB and BC?
Explanation:
The internal torque at a section is found from torque equilibrium of either side of the cut. In segment BC, the only external torque to the right is the 0.8 kN·m torque at C, so the internal torque magnitude is 0.8 kN·m. In segment AB, the net torque applied to the right is 2.0 - 0.8 = 1.2 kN·m. The opposite senses of the applied torques must be accounted for algebraically rather than adding their magnitudes. Therefore Option B is correct.
వివరణ:
Question 13
ప్రశ్న 13
A solid circular shaft of diameter 50 mm is limited to a maximum torsional shear stress of 50 MPa and rotates at 600 rpm. What is the maximum power it can transmit based on strength?
Explanation:
The torque capacity of a solid shaft is T = τallow πd³/16. With d = 50 mm and τallow = 50 MPa, the allowable torque is approximately 1.2272 kN·m. At 600 rpm, the angular velocity is 2π × 600/60 = 62.832 rad/s. The transmitted power is therefore about 1.2272 × 62.832 = 77.11 kW. Hence Option C is correct.
వివరణ:
Question 14
ప్రశ్న 14
A shaft transmits 100 kW while carrying a torque of 2.0 kN·m. What rotational speed is required approximately?
Explanation:
Using P = Tω, the required angular velocity is ω = 100000/2000 = 50 rad/s. Rotational speed is related to angular velocity by N = 60ω/(2π). Substitution gives N ≈ 477.46 rpm. The conversion must use torque in N·m and power in watts for consistency. Therefore Option C is correct.
వివరణ:
Question 15
ప్రశ్న 15
A shaft rotates at 1200 rpm. What is its angular velocity approximately?
Explanation:
One revolution corresponds to 2π radians. A speed of 1200 rpm therefore corresponds to 1200 × 2π radians per minute. Dividing by 60 converts the value to radians per second. The result is 40π ≈ 125.66 rad/s. Hence Option C is correct.
వివరణ:
Question 16
ప్రశ్న 16
A solid circular shaft 3 m long carries a torque of 2 kN·m. If G = 80 GPa and the angle of twist must not exceed 0.5°, what minimum theoretical diameter is required based on stiffness?
Explanation:
For a solid shaft, θ = 32TL/(πGd⁴). The allowable rotation is 0.5° = 0.0087266 rad. Substituting T = 2 × 10^6 N·mm, L = 3000 mm and G = 80000 N/mm² gives d⁴ from the stiffness equation. Taking the fourth root gives d ≈ 96.73 mm. Therefore Option C is correct.
వివరణ:
Question 17
ప్రశ్న 17
A hollow circular shaft and a solid shaft have the same material, length and outside diameter of 90 mm. The hollow shaft has an inside diameter of 60 mm. What is the ratio of the hollow-shaft torsional stiffness to that of the solid shaft?
Explanation:
For the same material and length, torsional stiffness is proportional to J. The solid shaft has Jsolid = πD⁴/32. The hollow shaft has Jhollow = π(D⁴ - d⁴)/32. Therefore the ratio is 1 - (60/90)⁴ = 1 - (2/3)⁴. This equals approximately 0.8025, so Option C is correct.
వివరణ:
Question 18
ప్రశ్న 18
A hollow shaft with D = 80 mm and d = 50 mm is 2 m long and has G = 80 GPa. If allowable shear stress is 70 MPa and allowable twist is 1°, which torque limitation governs?
Explanation:
For the hollow section, J = π(80⁴ - 50⁴)/32. The strength limit obtained from T = τallow J/R is approximately 5.963 kN·m. The stiffness limit obtained from T = θGJ/L with θ = 1° is approximately 2.379 kN·m. The smaller allowable torque is the controlling design value because both requirements must be satisfied. Therefore stiffness governs and Option B is correct.
వివరణ:
Question 19
ప్రశ్న 19
The hollow shaft in the previous question is governed by a permissible torque of approximately 2.379 kN·m. If it rotates at 300 rpm, what maximum power can it transmit while satisfying both the stated strength and twist limits?
Explanation:
At 300 rpm, the angular velocity is 2π × 300/60 = 31.416 rad/s. The governing permissible torque is approximately 2.379 kN·m, or 2379 N·m. Power is P = Tω. Thus P ≈ 2379 × 31.416 = 74738 W. Therefore the permissible power is approximately 74.74 kW and Option C is correct.
వివరణ:
Question 20
ప్రశ్న 20
A shaft transmits constant power. If its rotational speed is doubled while transmission losses are neglected, what happens to the transmitted torque?
Explanation:
Power transmission is governed by P = Tω. At constant power, torque is therefore inversely proportional to angular velocity. Rotational speed in rpm is directly proportional to angular velocity. Doubling rotational speed consequently reduces the required torque to one-half. Hence Option B is correct.
వివరణ:
Question 21
ప్రశ్న 21
Two geometrically similar solid circular shafts transmit the same constant power, but Shaft B rotates at twice the speed of Shaft A. If both are designed for the same allowable torsional shear stress, what is the ratio dB/dA?
Explanation:
At the same power, doubling rotational speed halves the transmitted torque. For a strength-controlled solid circular shaft, diameter varies as T^(1/3). Therefore dB/dA = (1/2)^(1/3). This evaluates to approximately 0.7937. Hence Option C is correct.
వివరణ:
Question 22
ప్రశ్న 22
A hollow shaft and a solid shaft have the same outside diameter D and are subjected to the same allowable maximum shear stress. If the hollow shaft has inside diameter d = 0.6D, what is the ratio of its torque capacity to that of the solid shaft?
Explanation:
For equal outside diameter and allowable shear stress, torque capacity is proportional to polar section modulus. The ratio is therefore (D⁴ - d⁴)/D⁴. With d/D = 0.6, this becomes 1 - 0.6⁴. Since 0.6⁴ = 0.1296, the ratio is 0.8704. Therefore Option C is correct.
వివరణ:
Question 23
ప్రశ్న 23
A hollow shaft has outside diameter 100 mm and inside diameter 80 mm. A solid shaft of the same material and length has the same cross-sectional area. If both have the same allowable torsional shear stress, approximately what is the ratio of hollow-shaft torque capacity to solid-shaft torque capacity?
Explanation:
Equal cross-sectional area gives the equivalent solid diameter as √(100² - 80²) = 60 mm. At equal allowable shear stress, torque capacity is proportional to polar section modulus. The hollow-section polar section modulus divided by that of the 60 mm solid shaft is approximately 2.733. This demonstrates the strength advantage obtained by distributing material farther from the shaft axis. Therefore Option C is correct.
వివరణ:
Question 24
ప్రశ్న 24
Consider the following statements about shaft design and power transmission:
1. At constant transmitted power, torque decreases as rotational speed increases.
2. For a solid shaft designed only by torsional strength, required diameter varies as the cube root of torque.
3. For a solid shaft designed only by angle-of-twist limitation, required diameter varies as the fourth root of torque.
4. When both strength and stiffness limits apply, the design should use the smaller of the diameters calculated from the two criteria.
Which statements are correct?
1. At constant transmitted power, torque decreases as rotational speed increases.
2. For a solid shaft designed only by torsional strength, required diameter varies as the cube root of torque.
3. For a solid shaft designed only by angle-of-twist limitation, required diameter varies as the fourth root of torque.
4. When both strength and stiffness limits apply, the design should use the smaller of the diameters calculated from the two criteria.
Which statements are correct?
Explanation:
Statement 1 follows from P = Tω and is correct. Statement 2 follows from τmax being proportional to T/d³ for a solid shaft. Statement 3 follows from θ being proportional to T/d⁴ for fixed length and material. Statement 4 is incorrect because the shaft must satisfy both criteria, so the larger required diameter must be selected. Therefore Statements 1, 2 and 3 are correct and Option B is the unique answer.
వివరణ:
Question 25
ప్రశ్న 25
Match each shaft-design quantity with the correct relationship:
1. Angular velocity for speed N rpm
2. Power transmitted by a rotating shaft
3. Torsional stiffness of a uniform shaft segment
4. Total twist of shaft segments connected in series
P. GJ/L
Q. Sum of the individual segment twists
R. 2πN/60
S. Tω
Which matching is correct?
1. Angular velocity for speed N rpm
2. Power transmitted by a rotating shaft
3. Torsional stiffness of a uniform shaft segment
4. Total twist of shaft segments connected in series
P. GJ/L
Q. Sum of the individual segment twists
R. 2πN/60
S. Tω
Which matching is correct?
Explanation:
Rotational speed N in rpm is converted to angular velocity using ω = 2πN/60, so item 1 matches R. Shaft power is P = Tω, so item 2 matches S. The torque required per unit end rotation of a uniform shaft segment is GJ/L, making item 3 match P. For shaft segments in series, compatible end rotations accumulate, so total twist is the algebraic sum of the individual twists and item 4 matches Q. Therefore Option A is correct.
వివరణ:
Answer Key సమాధానాల పట్టిక
-
Question 1 ప్రశ్న 1Answer: B. P = Tω సమాధానం: B.
-
Question 2 ప్రశ్న 2Answer: B. 954.9 N·m సమాధానం: B.
-
Question 3 ప్రశ్న 3Answer: D. 2865 N·m సమాధానం: D.
-
Question 4 ప్రశ్న 4Answer: C. 62.4 mm సమాధానం: C.
-
Question 5 ప్రశ్న 5Answer: C. 250.6 kW సమాధానం: C.
-
Question 6 ప్రశ్న 6Answer: B. 46.51 kW సమాధానం: B.
-
Question 7 ప్రశ్న 7Answer: A. Strength requires about 50.6 mm and stiffness about 59.3 mm; therefore stiffness governs. సమాధానం: A.
-
Question 8 ప్రశ్న 8Answer: B. Strength-controlled diameter varies as T^(1/3), while twist-controlled diameter varies as T^(1/4). సమాధానం: B.
-
Question 9 ప్రశ్న 9Answer: C. 2.36 times సమాధానం: C.
-
Question 10 ప్రశ్న 10Answer: C. 3.57 సమాధానం: C.
-
Question 11 ప్రశ్న 11Answer: B. 0.04648 rad or 2.66° సమాధానం: B.
-
Question 12 ప్రశ్న 12Answer: B. TAB = 1.2 kN·m and TBC = 0.8 kN·m సమాధానం: B.
-
Question 13 ప్రశ్న 13Answer: C. 77.11 kW సమాధానం: C.
-
Question 14 ప్రశ్న 14Answer: C. 477.5 rpm సమాధానం: C.
-
Question 15 ప్రశ్న 15Answer: C. 125.66 rad/s సమాధానం: C.
-
Question 16 ప్రశ్న 16Answer: C. 96.7 mm సమాధానం: C.
-
Question 17 ప్రశ్న 17Answer: C. 0.802 సమాధానం: C.
-
Question 18 ప్రశ్న 18Answer: B. Strength permits about 5.96 kN·m and stiffness about 2.38 kN·m, so stiffness governs. సమాధానం: B.
-
Question 19 ప్రశ్న 19Answer: C. 74.74 kW సమాధానం: C.
-
Question 20 ప్రశ్న 20Answer: B. It becomes one-half. సమాధానం: B.
-
Question 21 ప్రశ్న 21Answer: C. 0.794 సమాధానం: C.
-
Question 22 ప్రశ్న 22Answer: C. 0.8704 సమాధానం: C.
-
Question 23 ప్రశ్న 23Answer: C. 2.73 సమాధానం: C.
-
Question 24 ప్రశ్న 24Answer: B. 1, 2 and 3 only సమాధానం: B.
-
Question 25 ప్రశ్న 25Answer: A. 1-R, 2-S, 3-P, 4-Q సమాధానం: A.
