Please keep at least one language enabled. || కనీసం ఒక భాషను ఎంచుకోండి.
Question 1
ప్రశ్న 1
Which set of assumptions is appropriate for the elementary elastic-torsion theory of a prismatic circular shaft?
Explanation:
Elementary torsion theory for circular shafts assumes elastic material behaviour so that shear stress is proportional to shear strain. The material is generally treated as homogeneous, and isotropy is normally included in the classical formulation. Circular cross-sections remain plane and do not warp under uniform Saint-Venant torsion. Radial lines remain straight while rotating through the twist angle. Therefore Option A correctly states the assumptions underlying the elementary circular-shaft torsion equation.
వివరణ:
Question 2
ప్రశ్న 2
For a uniform circular shaft of length L subjected to a constant torque T within the linear-elastic range, which relation is the torsion equation?
Explanation:
The elastic torsion equation for a circular shaft is T/J = τ/r = Gθ/L. Here J is the polar second moment of area of the shaft cross-section. The shear stress τ at any material point is proportional to its radial distance r from the shaft axis. The quantity Gθ/L represents the shear-stress gradient with radius for a uniform shaft segment. Therefore Option B is correct.
వివరణ:
Question 3
ప్రశ్న 3
What is the polar second moment of area J of a solid circular shaft of diameter d?
Explanation:
For a solid circular area of radius R, the polar second moment is J = πR^4/2. Substituting R = d/2 gives J = π(d/2)^4/2. Simplification produces J = πd^4/32. This geometric property controls both torsional stress and torsional stiffness. Therefore Option A is correct.
వివరణ:
Question 4
ప్రశ్న 4
For a hollow circular shaft having outside diameter D and inside diameter d, what is its polar second moment of area?
Explanation:
The polar second moment of a hollow circular section is obtained by subtracting the inner circular contribution from the outer one. The outer solid circle contributes πD^4/32. The removed inner circle contributes πd^4/32. Their difference is therefore π(D^4 - d^4)/32. Hence Option C is correct.
వివరణ:
Question 5
ప్రశ్న 5
Which pair correctly gives the polar section modulus Zp = J/R for a solid circular shaft of diameter d and a hollow circular shaft of outside diameter D and inside diameter d, respectively?
Explanation:
Polar section modulus is defined as J divided by the outer radius at which maximum torsional shear stress occurs. For a solid shaft, J = πd^4/32 and R = d/2, giving Zp = πd^3/16. For a hollow shaft, J = π(D^4 - d^4)/32 and the outer radius is D/2. Hence Zp = π(D^4 - d^4)/(16D). Therefore Option A is correct.
వివరణ:
Question 6
ప్రశ్న 6
How does elastic torsional shear stress vary across the radius of a solid circular shaft?
Explanation:
The torsion equation gives τ = Tr/J for a circular shaft. For fixed torque and cross-sectional geometry, shear stress is directly proportional to radial distance r. At the shaft axis, r = 0 and hence the torsional shear stress is zero. At the outer surface, r is maximum and so the shear stress is maximum. Therefore Option B is correct.
వివరణ:
Question 7
ప్రశ్న 7
A hollow circular shaft has inside diameter d and outside diameter D. Under elastic torsion, what is the ratio of the shear stress at the inner surface to that at the outer surface?
Explanation:
For a circular shaft, torsional shear stress varies according to τ = Tr/J. Both the inner and outer surfaces belong to the same cross-section and therefore have the same values of T and J. Their stress ratio is consequently equal to their radius ratio. Since the radii are d/2 and D/2, τinner/τouter = d/D. Therefore Option B is correct.
వివరణ:
Question 8
ప్రశ్న 8
A solid circular shaft of diameter 50 mm transmits a torque of 1 kN·m. What is the maximum elastic torsional shear stress approximately?
Explanation:
For a solid circular shaft, the maximum torsional shear stress is τmax = 16T/(πd^3). The applied torque is 1 kN·m = 1 × 10^6 N·mm. Substitution gives τmax = 16 × 10^6/[π(50)^3]. This evaluates to approximately 40.74 N/mm², or 40.74 MPa. Therefore Option C is correct.
వివరణ:
Question 9
ప్రశ్న 9
A hollow circular shaft has outside diameter 60 mm and inside diameter 40 mm and carries a torque of 1.5 kN·m. What is the maximum elastic torsional shear stress approximately?
Explanation:
The polar second moment is J = π(60^4 - 40^4)/32 ≈ 1.021 × 10^6 mm^4. The outer radius is 30 mm. Using τmax = TR/J with T = 1.5 × 10^6 N·mm gives τmax = 1.5 × 10^6 × 30/(1.021 × 10^6). The result is approximately 44.07 MPa. Hence Option C is correct.
వివరణ:
Question 10
ప్రశ్న 10
A solid circular shaft 40 mm in diameter and 2 m long carries a torque of 0.5 kN·m. If G = 80 GPa, what is its angle of twist approximately?
Explanation:
For the solid shaft, J = π(40)^4/32 ≈ 251327 mm^4. The angle of twist is θ = TL/(GJ). Using T = 0.5 × 10^6 N·mm, L = 2000 mm and G = 80000 N/mm² gives θ ≈ 0.04974 rad. Converting to degrees gives approximately 2.85 degrees. Therefore Option C is correct.
వివరణ:
Question 11
ప్రశ్న 11
A hollow circular shaft has D = 80 mm, d = 60 mm and length 3 m. It carries a torque of 2 kN·m and has shear modulus G = 75 GPa. What is the angle of twist approximately?
Explanation:
The polar second moment is J = π(80^4 - 60^4)/32 ≈ 2.749 × 10^6 mm^4. The angle of twist is θ = TL/(GJ). Substitution of T = 2 × 10^6 N·mm, L = 3000 mm and G = 75000 N/mm² gives θ ≈ 0.02910 rad. This corresponds to approximately 1.667 degrees. Hence Option B is correct.
వివరణ:
Question 12
ప్రశ్న 12
A solid circular shaft carries a fixed torque. If its diameter is doubled while all other relevant conditions remain unchanged, what happens to its maximum torsional shear stress?
Explanation:
For a solid circular shaft, τmax = 16T/(πd^3). With torque fixed, maximum shear stress varies inversely with the cube of diameter. Doubling d therefore increases d^3 by a factor of eight. The stress consequently becomes one-eighth of its original value. Therefore Option C is correct.
వివరణ:
Question 13
ప్రశ్న 13
A solid circular shaft has fixed length, material and applied torque. If its diameter is doubled, what happens to its elastic angle of twist?
Explanation:
The angle of twist is θ = TL/(GJ). For a solid circular shaft, J is proportional to d^4. Doubling the diameter therefore increases J by a factor of 16. With T, L and G unchanged, angle of twist becomes one-sixteenth of the original value. Hence Option C is correct.
వివరణ:
Question 14
ప్రశ్న 14
A solid shaft and a hollow shaft have the same outside diameter of 60 mm and carry the same torque. The hollow shaft has an inside diameter of 40 mm. Approximately what is the ratio of the maximum shear stress in the hollow shaft to that in the solid shaft?
Explanation:
Both shafts have the same outer radius, so the stress ratio for equal torque depends inversely on their polar second moments. The solid shaft has Jsolid = π60^4/32. The hollow shaft has Jhollow = π(60^4 - 40^4)/32. Thus τhollow/τsolid = Jsolid/Jhollow ≈ 1.246. Therefore Option C is correct.
వివరణ:
Question 15
ప్రశ్న 15
A solid circular shaft of diameter 60 mm is limited to a maximum torsional shear stress of 80 MPa. What is its maximum elastic torque capacity approximately?
Explanation:
For a solid circular shaft, the polar section modulus is Zp = πd^3/16. With d = 60 mm, Zp ≈ 42411.5 mm^3. The allowable torque is T = τallow Zp. Thus T = 80 × 42411.5 ≈ 3.393 × 10^6 N·mm. Therefore the torque capacity is approximately 3.393 kN·m and Option C is correct.
వివరణ:
Question 16
ప్రశ్న 16
A hollow circular shaft has outside diameter 80 mm and inside diameter 50 mm. If the allowable torsional shear stress is 70 MPa, what is its maximum elastic torque capacity approximately?
Explanation:
The hollow-shaft polar section modulus is Zp = π(D^4 - d^4)/(16D). For D = 80 mm and d = 50 mm, Zp ≈ 85191 mm^3. The permissible torque is T = τallow Zp. Substitution gives T ≈ 70 × 85191 = 5.963 × 10^6 N·mm. Thus the capacity is approximately 5.96 kN·m and Option C is correct.
వివరణ:
Question 17
ప్రశ్న 17
In a solid circular shaft under elastic torsion, the maximum shear stress at the surface is 90 MPa. What is the shear stress at a radius equal to 0.6 times the outer radius?
Explanation:
Elastic torsional shear stress in a circular shaft varies linearly with radial distance. Therefore τ/τmax = r/R. At r = 0.6R, the local stress is 0.6 times the surface value. Thus τ = 0.6 × 90 = 54 MPa. Therefore Option C is correct.
వివరణ:
Question 18
ప్రశ్న 18
Which statement correctly distinguishes torsional rigidity from torsional stiffness for a uniform circular shaft?
Explanation:
The quantity GJ is commonly called the torsional rigidity of a circular shaft. The angle-of-twist relation is θ = TL/(GJ). Rearranging gives T/θ = GJ/L for a uniform shaft. Thus GJ/L is the rotational or torsional stiffness of a shaft segment of length L. Therefore Option A is correct.
వివరణ:
Question 19
ప్రశ్న 19
A stepped shaft consists of two segments connected in series and carrying the same torque of 1 kN·m. Segment 1 is a solid 40 mm diameter shaft 1 m long, and Segment 2 is a hollow shaft with D = 50 mm, d = 30 mm and length 1.5 m. If G = 80 GPa for both segments, what is the total angle of twist approximately?
Explanation:
For shaft segments in series, their relative end rotations add algebraically. Segment 1 twists by T L1/(GJ1) ≈ 0.04974 rad. Segment 2 twists by T L2/(GJ2) ≈ 0.03511 rad. Their total twist is therefore approximately 0.08484 rad. This is about 4.86 degrees, so Option C is correct.
వివరణ:
Question 20
ప్రశ్న 20
A hollow circular shaft has D = 80 mm, d = 60 mm, length 3 m and G = 75 GPa. What is its torsional stiffness T/θ approximately?
Explanation:
For a uniform shaft, torsional stiffness is k = GJ/L. The polar second moment for the given hollow section is approximately 2.749 × 10^6 mm^4. Therefore k = 75000 × 2.749 × 10^6/3000 ≈ 68.72 × 10^6 N·mm/rad. Since 10^6 N·mm equals 1 kN·m, the stiffness is approximately 68.72 kN·m/rad. Hence Option C is correct.
వివరణ:
Question 21
ప్రశ్న 21
A solid circular shaft of diameter 60 mm and a hollow shaft of outside diameter 75 mm and inside diameter 45 mm have equal cross-sectional areas. If both carry the same torque, approximately what is the ratio of the hollow-shaft maximum shear stress to the solid-shaft maximum shear stress?
Explanation:
The two sections have equal area because 75² - 45² = 60². The solid-shaft polar section modulus is approximately 42411.5 mm³. The hollow-shaft polar section modulus is approximately 72099.6 mm³, which is 1.70 times larger. For equal torque, maximum shear stress varies inversely with polar section modulus. Therefore τhollow/τsolid = 1/1.70 ≈ 0.588, making Option A correct.
వివరణ:
Question 22
ప్రశ్న 22
A solid circular shaft 2 m long transmits a torque of 1.2 kN·m. The allowable shear stress is 60 MPa, the allowable angle of twist is 1°, and G = 80 GPa. Ignoring standard-size rounding, what minimum diameter satisfies both limits?
Explanation:
The shear-stress condition gives d = [16T/(πτallow)]^(1/3) ≈ 46.7 mm. The twist condition uses θ = 32TL/(πGd^4) with θallow = π/180 rad. Solving the twist condition gives d ≈ 64.69 mm. Because both criteria must be satisfied, the larger required diameter governs. Therefore the theoretical minimum is approximately 64.7 mm and Option C is correct.
వివరణ:
Question 23
ప్రశ్న 23
A solid 50 mm diameter shaft carries a torque of 1 kN·m and has G = 80 GPa. What is the maximum elastic shear strain at its outer surface approximately?
Explanation:
The maximum shear stress for this shaft is approximately 40.74 MPa. Within the linear-elastic range, shear stress and shear strain are related by τ = Gγ. Therefore γmax = 40.74/80000 when G is expressed in MPa. This gives approximately 0.000509. Hence Option B is correct.
వివరణ:
Question 24
ప్రశ్న 24
Consider the following statements about elastic torsion of circular shafts:
1. Torsional shear stress varies linearly with radial distance from the shaft axis.
2. For a solid circular shaft, shear stress is zero at the centre and maximum at the outer surface.
3. Angle of twist of a uniform shaft is directly proportional to GJ.
4. For a hollow circular shaft, J = π(D^4 - d^4)/32.
Which statements are correct?
1. Torsional shear stress varies linearly with radial distance from the shaft axis.
2. For a solid circular shaft, shear stress is zero at the centre and maximum at the outer surface.
3. Angle of twist of a uniform shaft is directly proportional to GJ.
4. For a hollow circular shaft, J = π(D^4 - d^4)/32.
Which statements are correct?
Explanation:
Statement 1 is correct because τ = Tr/J gives a linear variation with radius. Statement 2 is correct for a solid circular shaft because r ranges from zero at the centre to the outer radius. Statement 3 is incorrect because θ = TL/(GJ), so angle of twist is inversely proportional to GJ. Statement 4 is the correct polar second moment for a hollow circular shaft. Therefore Statements 1, 2 and 4 are correct and Option B is the unique answer.
వివరణ:
Question 25
ప్రశ్న 25
Match each torsion quantity with its correct expression for a circular shaft:
1. Solid-shaft polar moment of area
2. Hollow-shaft polar moment of area
3. Maximum shear stress
4. Angle of twist of a uniform shaft
P. TR/J
Q. TL/(GJ)
R. πd^4/32
S. π(D^4 - d^4)/32
Which matching is correct?
1. Solid-shaft polar moment of area
2. Hollow-shaft polar moment of area
3. Maximum shear stress
4. Angle of twist of a uniform shaft
P. TR/J
Q. TL/(GJ)
R. πd^4/32
S. π(D^4 - d^4)/32
Which matching is correct?
Explanation:
The polar second moment of a solid circular shaft is πd^4/32, so item 1 matches R. For a hollow circular shaft it is π(D^4 - d^4)/32, so item 2 matches S. Maximum elastic torsional shear stress occurs at the outer radius and is TR/J, so item 3 matches P. The elastic angle of twist of a uniform shaft is TL/(GJ), so item 4 matches Q. Therefore Option A gives the correct complete matching.
వివరణ:
Answer Key సమాధానాల పట్టిక
-
Question 1 ప్రశ్న 1Answer: A. The material is homogeneous and linearly elastic, cross-sections remain plane and undistorted after twisting, and radial lines remain straight. సమాధానం: A.
-
Question 2 ప్రశ్న 2Answer: B. T/J = τ/r = Gθ/L సమాధానం: B.
-
Question 3 ప్రశ్న 3Answer: A. πd^4/32 సమాధానం: A.
-
Question 4 ప్రశ్న 4Answer: C. π(D^4 - d^4)/32 సమాధానం: C.
-
Question 5 ప్రశ్న 5Answer: A. πd^3/16 and π(D^4 - d^4)/(16D) సమాధానం: A.
-
Question 6 ప్రశ్న 6Answer: B. It varies linearly from zero at the centre to a maximum at the outer surface. సమాధానం: B.
-
Question 7 ప్రశ్న 7Answer: B. d/D సమాధానం: B.
-
Question 8 ప్రశ్న 8Answer: C. 40.74 MPa సమాధానం: C.
-
Question 9 ప్రశ్న 9Answer: C. 44.07 MPa సమాధానం: C.
-
Question 10 ప్రశ్న 10Answer: C. 0.04974 rad or 2.850° సమాధానం: C.
-
Question 11 ప్రశ్న 11Answer: B. 0.02910 rad or 1.667° సమాధానం: B.
-
Question 12 ప్రశ్న 12Answer: C. It becomes one-eighth. సమాధానం: C.
-
Question 13 ప్రశ్న 13Answer: C. It becomes one-sixteenth. సమాధానం: C.
-
Question 14 ప్రశ్న 14Answer: C. 1.246 సమాధానం: C.
-
Question 15 ప్రశ్న 15Answer: C. 3.393 kN·m సమాధానం: C.
-
Question 16 ప్రశ్న 16Answer: C. 5.96 kN·m సమాధానం: C.
-
Question 17 ప్రశ్న 17Answer: C. 54 MPa సమాధానం: C.
-
Question 18 ప్రశ్న 18Answer: A. Torsional rigidity is GJ, while torque required per unit end rotation for a shaft of length L is GJ/L. సమాధానం: A.
-
Question 19 ప్రశ్న 19Answer: C. 0.08484 rad or 4.86° సమాధానం: C.
-
Question 20 ప్రశ్న 20Answer: C. 68.72 kN·m/rad సమాధానం: C.
-
Question 21 ప్రశ్న 21Answer: A. 0.588 సమాధానం: A.
-
Question 22 ప్రశ్న 22Answer: C. 64.7 mm సమాధానం: C.
-
Question 23 ప్రశ్న 23Answer: B. 0.000509 సమాధానం: B.
-
Question 24 ప్రశ్న 24Answer: B. 1, 2 and 4 only సమాధానం: B.
-
Question 25 ప్రశ్న 25Answer: A. 1-R, 2-S, 3-P, 4-Q సమాధానం: A.
