Please keep at least one language enabled. || కనీసం ఒక భాషను ఎంచుకోండి.
Question 1
ప్రశ్న 1
For elastic bending about a specified neutral axis, how is the elastic section modulus Z corresponding to a particular extreme fibre defined?
Explanation:
The elastic section modulus is defined as the second moment of area divided by the distance from the neutral axis to the extreme fibre being considered. Thus Z = I/ymax. The maximum elastic bending stress can consequently be written as σmax = M/Z. For an unsymmetrical section, the distances to the two extreme fibres may differ, so separate section moduli may be required for the two sides. Therefore Option A is correct.
వివరణ:
Question 2
ప్రశ్న 2
Which statement about elastic section modulus is correct?
Explanation:
Section modulus is Z = I/y. The second moment of area has dimensions of length to the fourth power, while y has dimensions of length. Therefore Z has dimensions of length cubed, such as mm³ or m³. It depends on the geometry and bending axis of the section rather than directly on Young's modulus. Hence Option B is correct.
వివరణ:
Question 3
ప్రశ్న 3
What is the elastic section modulus of a rectangular section of width b and overall depth d about its centroidal axis parallel to the width?
Explanation:
For a rectangle about its centroidal axis parallel to the width, I = bd³/12. The extreme-fibre distance is d/2. Therefore Z = I/(d/2) = bd²/6. This section modulus directly gives the maximum elastic bending stress through σmax = M/Z. Hence Option A is correct.
వివరణ:
Question 4
ప్రశ్న 4
A rectangular beam section is 150 mm wide and 300 mm deep. It is subjected to a bending moment of 45 kN·m about its centroidal horizontal axis. What is the maximum bending-stress magnitude?
Explanation:
The rectangular section modulus is Z = bd²/6. Substitution gives Z = 150 × 300²/6 = 2.25 × 10^6 mm³. The bending moment is 45 kN·m = 45 × 10^6 N·mm. Therefore σmax = M/Z = 45 × 10^6/(2.25 × 10^6) = 20 MPa. Hence Option B is correct.
వివరణ:
Question 5
ప్రశ్న 5
A rectangular beam section 200 mm wide and 300 mm deep has an allowable bending stress of 12 MPa. What is its elastic moment of resistance about the centroidal horizontal axis?
Explanation:
The section modulus is Z = bd²/6 = 200 × 300²/6. This gives Z = 3.0 × 10^6 mm³. The allowable moment of resistance is M = σallow Z. Thus M = 12 × 3.0 × 10^6 = 36 × 10^6 N·mm = 36 kN·m. Therefore Option C is correct.
వివరణ:
Question 6
ప్రశ్న 6
A solid circular beam of diameter 120 mm carries a bending moment of 20 kN·m. What is the maximum bending-stress magnitude approximately?
Explanation:
For a solid circular section, the elastic section modulus is Z = πd³/32. For d = 120 mm, Z is approximately 169646 mm³. The applied moment is 20 × 10^6 N·mm. Hence σmax = 20 × 10^6/169646 ≈ 117.89 MPa. Therefore Option C is correct.
వివరణ:
Question 7
ప్రశ్న 7
A hollow circular beam has outside diameter 200 mm and inside diameter 120 mm. It carries a bending moment of 50 kN·m about a centroidal diameter. What is the maximum bending-stress magnitude approximately?
Explanation:
For the hollow circle, I = π(D⁴ - d⁴)/64. With D = 200 mm and d = 120 mm, I is approximately 68.361 × 10^6 mm⁴. The extreme-fibre distance is D/2 = 100 mm, so Z is approximately 683611 mm³. Therefore σmax = 50 × 10^6/683611 ≈ 73.14 MPa. Hence Option C is correct.
వివరణ:
Question 8
ప్రశ్న 8
For the hollow circular section with outside diameter 200 mm and inside diameter 120 mm, what bending moment can be resisted when the allowable extreme-fibre stress is 100 MPa?
Explanation:
The elastic section modulus of this hollow circular section is approximately 683611 mm³. Moment resistance is obtained from M = σallow Z. Thus M = 100 × 683611 = 68.361 × 10^6 N·mm. Converting units gives approximately 68.36 kN·m. Therefore Option C is correct.
వివరణ:
Question 9
ప్రశ్న 9
A rectangular hollow section has outside dimensions 200 mm wide by 300 mm deep and uniform wall thickness 20 mm. It is subjected to a bending moment of 80 kN·m about its centroidal horizontal axis. What is the maximum bending-stress magnitude approximately?
Explanation:
The inside dimensions are 160 mm by 260 mm. The centroidal second moment of area is I = [200 × 300³ - 160 × 260³]/12 ≈ 215.653 × 10^6 mm⁴. The extreme-fibre distance is 150 mm, giving Z ≈ 1.43769 × 10^6 mm³. Hence σmax = 80 × 10^6/1.43769 × 10^6 ≈ 55.64 MPa. Therefore Option B is correct.
వివరణ:
Question 10
ప్రశ్న 10
A symmetric built-up I-section has overall depth 300 mm, two flange plates each 150 mm × 20 mm, and a 10 mm thick web of clear depth 260 mm. What are its centroidal second moment of area and elastic section modulus about the horizontal symmetry axis approximately?
Explanation:
Because the built-up section is symmetric about its horizontal mid-depth, the neutral axis lies 150 mm from either extreme fibre. Each flange contribution is obtained using its own centroidal I plus the parallel-axis term Ad², with d = 140 mm. Adding both flange contributions and the web contribution gives I ≈ 132.45 × 10^6 mm⁴. Dividing by 150 mm gives Z ≈ 882.98 × 10^3 mm³. Therefore Option B is correct.
వివరణ:
Question 11
ప్రశ్న 11
The symmetric built-up I-section described as having I ≈ 132.45 × 10^6 mm⁴ and overall depth 300 mm is subjected to a bending moment of 60 kN·m. What is the maximum bending stress approximately?
Explanation:
The extreme-fibre distance is 150 mm. Thus the elastic section modulus is approximately 132.45 × 10^6/150 = 882.98 × 10^3 mm³. The bending moment is 60 × 10^6 N·mm. Hence σmax = M/Z ≈ 60 × 10^6/882978 = 67.95 MPa. Therefore Option C is correct.
వివరణ:
Question 12
ప్రశ్న 12
The same symmetric built-up I-section has an elastic section modulus of approximately 882.98 × 10^3 mm³. If its allowable bending stress is 160 MPa, what is its elastic moment of resistance approximately?
Explanation:
The elastic moment of resistance is M = σallow Z. Substitution gives M = 160 × 882978 N·mm. This equals approximately 141.28 × 10^6 N·mm. Converting to kN·m gives approximately 141.28 kN·m. Hence Option C is correct.
వివరణ:
Question 13
ప్రశ్న 13
A built-up I-section has identical top and bottom flanges and a centrally placed web. Before calculating bending stress about its horizontal symmetry axis, what can be concluded about the neutral-axis position?
Explanation:
Identical top and bottom flanges with a centrally placed web make the cross-section symmetric about its horizontal mid-depth. The centroid of a geometrically symmetric homogeneous section lies on that symmetry axis. Under simple bending without an axial resultant, the neutral axis passes through the centroid. The bending-moment magnitude does not determine the centroidal neutral-axis location. Therefore Option C is correct.
వివరణ:
Question 14
ప్రశ్న 14
For a homogeneous beam obeying the simple-bending assumptions, which statement correctly describes the longitudinal bending-stress distribution across the depth?
Explanation:
The flexure equation gives σ = My/I. For a given section and bending moment, stress is therefore directly proportional to the distance y from the neutral axis. It is zero where y = 0 at the neutral axis. Its magnitude increases linearly toward the outermost fibres. Therefore Option B correctly describes the elastic bending-stress distribution.
వివరణ:
Question 15
ప్రశ్న 15
A homogeneous cross-section is symmetric about the neutral axis used for bending. What relationship exists between the maximum tensile and compressive bending-stress magnitudes under pure bending?
Explanation:
For elastic bending, stress magnitude is proportional to distance from the neutral axis. A section symmetric about that axis has equal extreme-fibre distances on the two sides. Therefore the extreme tensile and compressive stresses have equal magnitudes for a given bending moment. Their signs are opposite because one side lengthens while the other shortens. Hence Option C is correct.
వివరణ:
Question 16
ప్రశ్న 16
A rectangular section 100 mm wide and 200 mm deep is first bent about its centroidal axis parallel to the 100 mm width. It is then rotated by 90° so that it is 200 mm wide and 100 mm deep and is subjected to the same bending moment. What is the ratio of the original maximum bending stress to the rotated-section maximum bending stress?
Explanation:
In the original orientation, Z = 100 × 200²/6 = 666667 mm³. In the rotated orientation, Z = 200 × 100²/6 = 333333 mm³. Maximum bending stress varies inversely with section modulus for the same moment. Therefore the original stress divided by the rotated stress is 333333/666667 = 1/2. Hence Option A is correct.
వివరణ:
Question 17
ప్రశ్న 17
The diameter of a solid circular beam is increased by 20 percent while the applied bending moment remains unchanged. Approximately what fraction of the original maximum bending stress remains?
Explanation:
For a solid circular section, Z = πd³/32. Maximum bending stress is therefore inversely proportional to d³ for a fixed bending moment. Increasing diameter by 20 percent multiplies section modulus by 1.2³ = 1.728. The new stress is consequently 1/1.728 ≈ 0.579 times the original stress. Therefore Option A is correct.
వివరణ:
Question 18
ప్రశ్న 18
For sections made from the same material and having the same total cross-sectional area, what generally improves elastic bending efficiency about a specified axis?
Explanation:
The second moment of area weights each differential area according to the square of its distance from the neutral axis. Moving material farther from that axis can therefore increase I substantially. A larger I generally produces a larger section modulus when the extreme-fibre geometry is suitably controlled. For a prescribed bending moment, a larger section modulus reduces the maximum elastic bending stress. Hence Option B describes the basic geometric reason for the efficiency of I-sections and hollow sections.
వివరణ:
Question 19
ప్రశ్న 19
For a hollow circular section with fixed outside diameter D, what happens to its elastic section modulus about a centroidal diameter as the inside diameter is increased, all else being equal?
Explanation:
For a hollow circle, I = π(D⁴ - d⁴)/64. Increasing the inside diameter d while holding D fixed reduces the difference D⁴ - d⁴ and therefore reduces I. The extreme-fibre distance remains D/2 because the outside diameter does not change. Consequently Z = I/(D/2) also decreases. Therefore Option C is correct.
వివరణ:
Question 20
ప్రశ్న 20
A beam section has I = 96 × 10^6 mm⁴ and its farthest extreme fibre is 120 mm from the neutral axis. If the allowable bending stress is 150 MPa, which pair correctly gives the elastic section modulus and moment of resistance?
Explanation:
The section modulus is Z = I/ymax. Thus Z = 96 × 10^6/120 = 800000 mm³. The moment of resistance is M = σallow Z. This gives M = 150 × 800000 = 120 × 10^6 N·mm = 120 kN·m. Therefore Option B is correct.
వివరణ:
Question 21
ప్రశ్న 21
A homogeneous unsymmetrical section has I = 60 × 10^6 mm⁴ about its centroidal neutral axis. The extreme fibres lie 120 mm above and 80 mm below the neutral axis. If the bending-moment magnitude is 30 kN·m, what are the extreme bending-stress magnitudes?
Explanation:
The bending-stress magnitude is σ = My/I. At the top extreme fibre, σ = 30 × 10^6 × 120/(60 × 10^6) = 60 MPa. At the bottom extreme fibre, the magnitude is 30 × 10^6 × 80/(60 × 10^6) = 40 MPa. The stresses have opposite signs under bending, although the question asks only for their magnitudes. Therefore Option B is correct.
వివరణ:
Question 22
ప్రశ్న 22
A homogeneous unsymmetrical section has I = 60 × 10^6 mm⁴ about its neutral axis, with extreme-fibre distances of 120 mm on one side and 80 mm on the other. If the allowable tensile and compressive bending-stress magnitudes are both 120 MPa, what is the maximum permissible bending-moment magnitude?
Explanation:
The section modulus to the farther extreme fibre is 60 × 10^6/120 = 500000 mm³. The section modulus to the nearer extreme fibre is 60 × 10^6/80 = 750000 mm³. Since the allowable tensile and compressive magnitudes are equal, the smaller section modulus governs. Thus Mmax = 120 × 500000 = 60 × 10^6 N·mm = 60 kN·m. Therefore Option B is correct.
వివరణ:
Question 23
ప్రశ్న 23
Two homogeneous beams made of different linearly elastic materials have identical cross-sectional geometry and are subjected to the same prescribed bending moment about the same axis. Assuming simple bending is valid for both, which statement about their maximum bending stresses is correct?
Explanation:
For a homogeneous beam under a prescribed bending moment, maximum elastic bending stress is σmax = M/Z. Both beams have the same cross-sectional geometry, so their section moduli are identical. They also carry the same prescribed bending moment. Young's modulus affects curvature through M/EI but does not appear in M/Z for the stress distribution under these conditions. Therefore Option C is correct.
వివరణ:
Question 24
ప్రశ్న 24
Match each cross-section with its elastic section-modulus expression about the stated centroidal bending axis:
1. Rectangle of width b and depth d
2. Solid circle of diameter d
3. Hollow circle of outside diameter D and inside diameter d
4. General section with extreme-fibre distance c
P. I/c
Q. πd³/32
R. bd²/6
S. π(D⁴ - d⁴)/(32D)
Which matching is correct?
1. Rectangle of width b and depth d
2. Solid circle of diameter d
3. Hollow circle of outside diameter D and inside diameter d
4. General section with extreme-fibre distance c
P. I/c
Q. πd³/32
R. bd²/6
S. π(D⁴ - d⁴)/(32D)
Which matching is correct?
Explanation:
For a rectangle, Z = bd²/6, so item 1 matches R. For a solid circle, Z = πd³/32, so item 2 matches Q. For a hollow circle, dividing I = π(D⁴ - d⁴)/64 by D/2 gives Z = π(D⁴ - d⁴)/(32D), so item 3 matches S. For any general elastic section relative to a specified extreme fibre, Z = I/c, so item 4 matches P. Therefore Option A gives the correct complete matching.
వివరణ:
Question 25
ప్రశ్న 25
Consider the following statements about bending stress and section modulus:
1. Elastic section modulus has dimensions of length cubed.
2. For a given bending moment, increasing section modulus reduces the extreme-fibre bending stress.
3. In a homogeneous symmetric section bent about its symmetry axis, equal extreme-fibre distances produce equal tensile and compressive stress magnitudes.
4. Removing material close to the neutral axis must always reduce section modulus by exactly the same percentage as the cross-sectional area removed.
Which statements are correct?
1. Elastic section modulus has dimensions of length cubed.
2. For a given bending moment, increasing section modulus reduces the extreme-fibre bending stress.
3. In a homogeneous symmetric section bent about its symmetry axis, equal extreme-fibre distances produce equal tensile and compressive stress magnitudes.
4. Removing material close to the neutral axis must always reduce section modulus by exactly the same percentage as the cross-sectional area removed.
Which statements are correct?
Explanation:
Statement 1 is correct because section modulus is I divided by a length and therefore has dimensions of length cubed. Statement 2 is correct because σmax = M/Z for elastic bending. Statement 3 is correct because stress is proportional to the extreme-fibre distance and the two distances are equal in a symmetric section. Statement 4 is incorrect because the effect of removing material on I depends strongly on the material's distance from the neutral axis and is not simply proportional to area removed. Therefore Statements 1, 2 and 3 are correct and Option B is the unique answer.
వివరణ:
Answer Key సమాధానాల పట్టిక
-
Question 1 ప్రశ్న 1Answer: A. Z = I/ymax సమాధానం: A.
-
Question 2 ప్రశ్న 2Answer: B. It has dimensions of length cubed and is a geometric property of the cross-section. సమాధానం: B.
-
Question 3 ప్రశ్న 3Answer: A. bd²/6 సమాధానం: A.
-
Question 4 ప్రశ్న 4Answer: B. 20 MPa సమాధానం: B.
-
Question 5 ప్రశ్న 5Answer: C. 36 kN·m సమాధానం: C.
-
Question 6 ప్రశ్న 6Answer: C. 117.89 MPa సమాధానం: C.
-
Question 7 ప్రశ్న 7Answer: C. 73.14 MPa సమాధానం: C.
-
Question 8 ప్రశ్న 8Answer: C. 68.36 kN·m సమాధానం: C.
-
Question 9 ప్రశ్న 9Answer: B. 55.64 MPa సమాధానం: B.
-
Question 10 ప్రశ్న 10Answer: B. I = 132.45 × 10^6 mm⁴ and Z = 882.98 × 10^3 mm³ సమాధానం: B.
-
Question 11 ప్రశ్న 11Answer: C. 67.95 MPa సమాధానం: C.
-
Question 12 ప్రశ్న 12Answer: C. 141.28 kN·m సమాధానం: C.
-
Question 13 ప్రశ్న 13Answer: C. It lies at the mid-depth because of geometric symmetry. సమాధానం: C.
-
Question 14 ప్రశ్న 14Answer: B. Stress varies linearly from zero at the neutral axis to maximum magnitude at the extreme fibres. సమాధానం: B.
-
Question 15 ప్రశ్న 15Answer: C. Their magnitudes are equal because the extreme-fibre distances are equal. సమాధానం: C.
-
Question 16 ప్రశ్న 16Answer: A. 1/2 సమాధానం: A.
-
Question 17 ప్రశ్న 17Answer: A. 0.579 సమాధానం: A.
-
Question 18 ప్రశ్న 18Answer: B. Distributing more material farther from the neutral axis, while maintaining the required geometry and stability. సమాధానం: B.
-
Question 19 ప్రశ్న 19Answer: C. It decreases because the second moment of area decreases while the extreme-fibre distance remains D/2. సమాధానం: C.
-
Question 20 ప్రశ్న 20Answer: B. Z = 800000 mm³ and M = 120 kN·m సమాధానం: B.
-
Question 21 ప్రశ్న 21Answer: B. Top 60 MPa and bottom 40 MPa సమాధానం: B.
-
Question 22 ప్రశ్న 22Answer: B. 60 kN·m సమాధానం: B.
-
Question 23 ప్రశ్న 23Answer: C. Their maximum bending stresses are equal because M and Z are the same. సమాధానం: C.
-
Question 24 ప్రశ్న 24Answer: A. 1-R, 2-Q, 3-S, 4-P సమాధానం: A.
-
Question 25 ప్రశ్న 25Answer: B. 1, 2 and 3 only సమాధానం: B.
