Please keep at least one language enabled. || కనీసం ఒక భాషను ఎంచుకోండి.
Question 1
ప్రశ్న 1
Which combination most appropriately represents the classical assumptions used in deriving the simple-bending flexure equation for a homogeneous beam?
Explanation:
Classical simple-bending theory assumes a homogeneous material that behaves elastically within the range being considered. It also assumes that plane cross-sections before bending remain plane after bending. The beam is treated as slender so that the radius of curvature is large compared with the cross-sectional dimensions. These assumptions lead to a linear longitudinal-strain distribution through the depth. Therefore Option A correctly represents the assumptions supporting the classical flexure equation.
వివరణ:
Question 2
ప్రశ్న 2
For a homogeneous linearly elastic beam under simple bending, which relationship is the flexure equation?
Explanation:
The classical flexure equation is M/I = σ/y = E/R. Here M is the bending moment at the section and I is the second moment of area about the neutral axis. The quantity σ is the longitudinal bending stress at a distance y from the neutral axis. The quantities E and R denote Young's modulus and the radius of curvature respectively. Therefore Option A gives the complete and dimensionally consistent bending relationship.
వివరణ:
Question 3
ప్రశ్న 3
The assumption that plane sections remain plane after bending leads most directly to which conclusion about longitudinal strain across the beam depth?
Explanation:
When initially plane cross-sections remain plane during bending, longitudinal fibres at different distances from the neutral surface undergo different changes in length in a geometrically regular manner. For a radius of curvature R, the longitudinal strain magnitude at distance y from the neutral axis is proportional to y/R. The strain is zero at the neutral axis and increases linearly toward the extreme fibres. Hooke's law then converts this linear strain distribution into a linear bending-stress distribution for a homogeneous linearly elastic material. Therefore Option B is correct.
వివరణ:
Question 4
ప్రశ్న 4
What is the neutral surface of a beam in simple bending?
Explanation:
The neutral surface consists of longitudinal fibres whose lengths do not change during bending. Consequently the longitudinal bending strain on this surface is zero. For a linearly elastic material, the corresponding longitudinal bending stress is also zero. The intersection of the neutral surface with a transverse cross-section is called the neutral axis. Therefore Option A correctly defines the neutral surface.
వివరణ:
Question 5
ప్రశ్న 5
For a homogeneous beam section made of one material and subjected to pure bending without a resultant axial force, why does the neutral axis pass through the centroid of the cross-section?
Explanation:
Pure bending produces a bending moment but no resultant axial force on the cross-section. Under simple-bending assumptions, the longitudinal stress is proportional to the distance from the neutral axis. Setting the integral of longitudinal stress over the complete cross-sectional area equal to zero requires the first moment of area about the neutral axis to vanish. For a homogeneous section with constant Young's modulus, this condition places the neutral axis through the centroid. Therefore Option A is correct.
వివరణ:
Question 6
ప్రశ్న 6
For a beam bent to a radius of curvature R, what is the magnitude of longitudinal bending strain at a fibre located a distance y from the neutral axis under the small-strain simple-bending model?
Explanation:
The neutral surface has radius of curvature R and experiences zero longitudinal strain. A fibre located a distance y from the neutral surface has a proportional difference in arc length. Under the small-strain bending geometry, the strain magnitude is therefore ε = y/R. The sign depends on whether the fibre is elongated or shortened relative to the neutral surface. Hence Option C is correct.
వివరణ:
Question 7
ప్రశ్న 7
Which expression represents the internal bending moment or moment of resistance of a cross-section due to the longitudinal bending stresses?
Explanation:
A differential area dA carrying longitudinal stress σ develops a differential longitudinal force σdA. Its moment about the neutral axis is σy dA, where y is its perpendicular distance from that axis. Integrating this contribution over the complete cross-section gives the internal resisting bending moment. Under equilibrium, this internal moment balances the externally applied bending moment at the section. Therefore the moment of resistance is represented by ∫A σy dA, making Option B correct.
వివరణ:
Question 8
ప్రశ్న 8
A rectangular beam section is 100 mm wide and 200 mm deep and is subjected to a bending moment of 10 kN·m about its centroidal horizontal axis. Assuming simple bending, what is the maximum bending stress?
Explanation:
For the rectangular section, I = bd³/12 = 100 × 200³/12 = 66.67 × 10^6 mm^4. The extreme-fibre distance from the neutral axis is y = 100 mm. The bending moment is 10 kN·m = 10 × 10^6 N·mm. Using σ = My/I gives σmax = 10 × 10^6 × 100/(66.67 × 10^6) = 15 MPa. Therefore Option C is correct.
వివరణ:
Question 9
ప్రశ్న 9
For the same 100 mm × 200 mm rectangular beam section carrying a 10 kN·m bending moment, what is the bending-stress magnitude at a fibre 50 mm from the neutral axis?
Explanation:
Bending stress varies linearly with distance from the neutral axis under the simple-bending assumptions. The extreme fibre at y = 100 mm carries a stress magnitude of 15 MPa. A fibre at y = 50 mm is located at one-half of that distance. Its stress magnitude is therefore one-half of 15 MPa, or 7.5 MPa. Hence Option B is correct.
వివరణ:
Question 10
ప్రశ్న 10
A rectangular beam section is 120 mm wide and 240 mm deep. If the allowable bending stress is 12 MPa, what is the moment of resistance about the centroidal axis?
Explanation:
The section modulus of a rectangular section about its centroidal axis is Z = bd²/6. Substitution gives Z = 120 × 240²/6 = 1.152 × 10^6 mm³. The moment of resistance at the allowable stress is M = σallow Z. Thus M = 12 × 1.152 × 10^6 = 13.824 × 10^6 N·mm, or 13.824 kN·m. Therefore Option C is correct.
వివరణ:
Question 11
ప్రశ్న 11
A solid circular beam of diameter 100 mm is subjected to a bending moment of 4 kN·m. What is the maximum bending stress approximately?
Explanation:
For a solid circular section, the section modulus is Z = πd³/32. For d = 100 mm, Z is approximately 98174.8 mm³. The bending moment is 4 kN·m = 4 × 10^6 N·mm. Therefore σmax = M/Z = 4 × 10^6/98174.8 ≈ 40.74 MPa. Hence Option C is correct.
వివరణ:
Question 12
ప్రశ్న 12
A homogeneous beam section has E = 200 GPa and I = 80 × 10^6 mm^4. If it is subjected to a constant bending moment of 20 kN·m, what is the radius of curvature under simple bending?
Explanation:
The curvature relation from the flexure equation is 1/R = M/(EI). The moment is 20 kN·m = 20 × 10^6 N·mm and E = 200000 N/mm². Substitution gives 1/R = 20 × 10^6/(200000 × 80 × 10^6) = 1.25 × 10^-6 mm^-1. Thus R = 800000 mm, which is equal to 800 m. Therefore Option D is correct.
వివరణ:
Question 13
ప్రశ్న 13
For the same homogeneous beam section subjected to the same bending moment, what happens to its curvature if Young's modulus is doubled while I remains unchanged?
Explanation:
For simple bending, curvature is 1/R = M/(EI). If M and I remain fixed, curvature is inversely proportional to Young's modulus E. Doubling E therefore reduces the curvature to one-half of its original value. Equivalently, the radius of curvature doubles. Hence Option B is correct.
వివరణ:
Question 14
ప్రశ్న 14
Two homogeneous beams have the same cross-sectional geometry and carry the same bending moment, but Beam 1 has twice the Young's modulus of Beam 2. Under simple-bending assumptions, which statement is correct?
Explanation:
For a homogeneous section subjected to a prescribed bending moment, the bending stress is σ = My/I. Since both beams have the same M, I and fibre coordinate y, their bending-stress distributions are identical. Curvature, however, is M/(EI). Doubling E therefore halves the curvature of Beam 1 compared with Beam 2. Consequently Option B is correct.
వివరణ:
Question 15
ప్రశ్న 15
Two homogeneous beams of the same material and cross-sectional shape are subjected to the same bending moment. Beam B has twice the second moment of area of Beam A, while the distance of the compared fibre from the neutral axis is the same. How does the bending stress at that fibre in Beam B compare with that in Beam A?
Explanation:
The bending stress at a specified fibre is σ = My/I. The bending moment M and the distance y are the same for both beams. Beam B has twice the second moment of area, so its denominator in the flexure expression is twice as large. Its bending stress is therefore one-half of the stress in Beam A. Hence Option C is correct.
వివరణ:
Question 16
ప్రశ్న 16
A rectangular beam has fixed width b and is subjected to the same bending moment before and after its depth is doubled. What happens to its maximum bending stress under simple bending?
Explanation:
For a rectangular section, the section modulus is Z = bd²/6. Maximum bending stress is σmax = M/Z. With width and bending moment fixed, σmax is therefore inversely proportional to d². Doubling the depth increases the section modulus by a factor of four. The maximum bending stress consequently becomes one-fourth of its original value, so Option B is correct.
వివరణ:
Question 17
ప్రశ్న 17
A homogeneous unsymmetrical cross-section is subjected to bending about a centroidal principal axis, with no resultant axial force. Which statement is correct under simple-bending assumptions?
Explanation:
For a homogeneous section under bending without a resultant axial force, the neutral axis passes through the centroid. The areas on the two sides of that axis do not have to be equal. Bending stress varies as σ = My/I, so its magnitude depends on the distance of a fibre from the neutral axis. If the extreme distances on the two sides are unequal, the maximum tensile and compressive stress magnitudes will also be unequal. Therefore Option B is correct.
వివరణ:
Question 18
ప్రశ్న 18
Why should the homogeneous-beam equation σ = My/I not be applied without qualification to an untransformed composite beam made of materials with different Young's moduli?
Explanation:
Perfectly bonded materials in a composite beam may share a compatible longitudinal-strain distribution. However, stress is related to strain through σ = Eε, so different Young's moduli produce different stresses for the same strain. The direct homogeneous formula σ = My/I assumes a single material modulus in its classical derivation. Composite bending therefore requires an appropriate transformed-section or equivalent compatibility-and-equilibrium treatment. Hence Option B is correct.
వివరణ:
Question 19
ప్రశ్న 19
Which statement best describes use of the elementary flexure formula in a slender beam region where transverse shear force is also present?
Explanation:
The classical derivation of the simple-bending equation is most direct for pure bending. In engineering beam analysis, the flexure formula is also commonly applied locally to slender beams carrying transverse loads when Euler-Bernoulli assumptions remain appropriate. The formula determines longitudinal normal stress caused by bending moment and does not itself determine transverse shear stress. Near concentrated load application points, abrupt geometric discontinuities, or in deep beams, the simple assumptions may be less accurate. Therefore the qualified statement in Option B is correct.
వివరణ:
Question 20
ప్రశ్న 20
Consider the following statements about simple bending:
1. Plane sections are assumed to remain plane after bending.
2. Longitudinal strain varies linearly through the depth.
3. For a homogeneous beam without resultant axial force, the neutral axis passes through the centroid.
4. The flexure equation assumes that the material may be arbitrarily nonlinear in the stress-strain range considered.
Which statements are correct?
1. Plane sections are assumed to remain plane after bending.
2. Longitudinal strain varies linearly through the depth.
3. For a homogeneous beam without resultant axial force, the neutral axis passes through the centroid.
4. The flexure equation assumes that the material may be arbitrarily nonlinear in the stress-strain range considered.
Which statements are correct?
Explanation:
Statement 1 is a fundamental kinematic assumption of classical simple-bending theory. Statement 2 follows from the plane-sections assumption and the geometry of bending. Statement 3 is correct for a homogeneous cross-section under bending with no resultant axial force. Statement 4 is incorrect because the classical relationship σ = Eε used in deriving M/I = σ/y = E/R requires linear-elastic behaviour over the stress range considered. Therefore Statements 1, 2 and 3 are correct and Option B is the unique answer.
వివరణ:
Question 21
ప్రశ్న 21
Beam A and Beam B carry the same bending moment and have the same distance y from the neutral axis to the fibre being examined. If IA = 40 × 10^6 mm^4 and IB = 80 × 10^6 mm^4, what is the ratio σA/σB?
Explanation:
The bending stress at the specified fibre is σ = My/I. Both beams have the same bending moment and the same value of y. Therefore their stress ratio is σA/σB = IB/IA. Substitution gives 80/40 = 2. Hence the stress in Beam A is twice that in Beam B and Option C is correct.
వివరణ:
Question 22
ప్రశ్న 22
At a beam section, the bending moment is 15 kN·m and the second moment of area about the neutral axis is 50 × 10^6 mm^4. What is the bending-stress magnitude at a fibre 40 mm from the neutral axis?
Explanation:
The flexure formula gives σ = My/I. The bending moment is 15 kN·m = 15 × 10^6 N·mm. Substitution gives σ = 15 × 10^6 × 40/(50 × 10^6). The resulting stress magnitude is 12 N/mm², which is 12 MPa. Therefore Option B is correct.
వివరణ:
Question 23
ప్రశ్న 23
A homogeneous beam has E = 200 GPa. At a fibre 100 mm from the neutral axis, the bending-stress magnitude is 100 MPa. What is the radius of curvature under simple bending?
Explanation:
From the flexure relationship, σ/y = E/R. Rearranging gives R = Ey/σ. Using E = 200000 MPa, y = 100 mm and σ = 100 MPa gives R = 200000 mm. This is equal to 200 m. Therefore Option C is correct.
వివరణ:
Question 24
ప్రశ్న 24
A beam is bent to a radius of curvature of 200 m. What is the magnitude of longitudinal bending strain at a fibre 150 mm from the neutral axis?
Explanation:
Longitudinal bending strain magnitude is ε = y/R. The fibre distance is 150 mm, while the radius of curvature is 200 m = 200000 mm. Therefore ε = 150/200000 = 0.00075. Because strain is a ratio of lengths, it is dimensionless. Hence Option B is correct.
వివరణ:
Question 25
ప్రశ్న 25
A simply supported beam of span 4 m has a rectangular cross-section 100 mm wide and 200 mm deep. It carries a single central point load W. If the allowable bending stress is 10 MPa and simple bending governs, what is the maximum permissible value of W?
Explanation:
The section modulus of the rectangle is Z = bd²/6 = 100 × 200²/6 = 666666.7 mm³. The allowable bending moment is therefore Mallow = σallow Z = 10 × 666666.7 = 6.667 × 10^6 N·mm, or 6.667 kN·m. For a simply supported beam carrying a central point load, the maximum bending moment is WL/4. Thus W = 4Mallow/L = 4 × 6.667/4 = 6.667 kN. Therefore Option B is correct.
వివరణ:
Answer Key సమాధానాల పట్టిక
-
Question 1 ప్రశ్న 1Answer: A. The material is homogeneous and linearly elastic, plane sections remain plane after bending, and the radius of curvature is large compared with the beam depth. సమాధానం: A.
-
Question 2 ప్రశ్న 2Answer: A. M/I = σ/y = E/R సమాధానం: A.
-
Question 3 ప్రశ్న 3Answer: B. Longitudinal strain varies linearly with distance from the neutral axis. సమాధానం: B.
-
Question 4 ప్రశ్న 4Answer: A. The surface containing longitudinal fibres that undergo no change in length due to bending. సమాధానం: A.
-
Question 5 ప్రశ్న 5Answer: A. Because the resultant longitudinal normal force obtained by integrating the linear bending stress over the area must be zero. సమాధానం: A.
-
Question 6 ప్రశ్న 6Answer: C. y/R సమాధానం: C.
-
Question 7 ప్రశ్న 7Answer: B. ∫A σy dA సమాధానం: B.
-
Question 8 ప్రశ్న 8Answer: C. 15 MPa సమాధానం: C.
-
Question 9 ప్రశ్న 9Answer: B. 7.5 MPa సమాధానం: B.
-
Question 10 ప్రశ్న 10Answer: C. 13.824 kN·m సమాధానం: C.
-
Question 11 ప్రశ్న 11Answer: C. 40.74 MPa సమాధానం: C.
-
Question 12 ప్రశ్న 12Answer: D. 800 m సమాధానం: D.
-
Question 13 ప్రశ్న 13Answer: B. Curvature becomes one-half. సమాధానం: B.
-
Question 14 ప్రశ్న 14Answer: B. Beam 1 and Beam 2 have the same bending-stress distribution, but Beam 1 has one-half the curvature. సమాధానం: B.
-
Question 15 ప్రశ్న 15Answer: C. It is one-half as large. సమాధానం: C.
-
Question 16 ప్రశ్న 16Answer: B. It becomes one-fourth. సమాధానం: B.
-
Question 17 ప్రశ్న 17Answer: B. The neutral axis passes through the centroid, but the extreme tensile and compressive stress magnitudes may differ if the extreme-fibre distances are unequal. సమాధానం: B.
-
Question 18 ప్రశ్న 18Answer: B. Because compatible strain does not generally produce the same stress at a given y in materials having different Young's moduli. సమాధానం: B.
-
Question 19 ప్రశ్న 19Answer: B. The formula is commonly used for longitudinal bending stress in slender-beam regions where Euler-Bernoulli assumptions remain adequate, but it should not be treated as an exact description near major discontinuities or where shear deformation is significant. సమాధానం: B.
-
Question 20 ప్రశ్న 20Answer: B. 1, 2 and 3 only సమాధానం: B.
-
Question 21 ప్రశ్న 21Answer: C. 2 సమాధానం: C.
-
Question 22 ప్రశ్న 22Answer: B. 12 MPa సమాధానం: B.
-
Question 23 ప్రశ్న 23Answer: C. 200 m సమాధానం: C.
-
Question 24 ప్రశ్న 24Answer: B. 0.00075 సమాధానం: B.
-
Question 25 ప్రశ్న 25Answer: B. 6.67 kN సమాధానం: B.
